5 Best Orbital Sander Replacement Pads (November 2026)
The best orbital sander replacement pads include the Gnellkoor Orbital Sander Pad Replacement for Dewalt for DeWalt 4-screw fit, the Poweka 5”ROS20vs Replacement Sanding Pad Compatible for Bosch ROS10 and ROS20VS, and the NYXCL 5 inch DeWalt DWE6423/6423K for a pad and abrasive bundle.
On this page (5 sections)
The best orbital sander replacement pad for most DeWalt users is the Gnellkoor 2 Pack, with a 5-inch diameter, 4 screw holes and 8 dust holes. Choose Poweka for Bosch ROS10 or ROS20VS sanders, AxPower for several 3-screw machines, or DEWALT for the DWE64233 model match.
That short list shows why fit matters more than the name alone. All of these pads are 5 inches, yet the mounting and model details change which sander each one suits.
A backing pad affects more than the sandpaper connection. Diameter controls the sanding-disc size, the screw pattern determines whether the pad can mount, and dust holes need to line up with the sander and disc.
For a flat panel, a firm pad keeps the abrasive spread evenly across the surface. That can make wide, controlled passes easier and reduce the risk of digging in at one edge.
For a shaped or uneven workpiece, the same firmness can feel limiting. The pad may bridge across a curve, so contact becomes patchy and the finish changes from one area to the next.
Care also starts before you sand. A pad that is seated squarely and holds the disc flat will behave differently from one that is slightly off centre, even when the diameter looks correct.
If you are still comparing tool types, our guide to different types of sanders explains where random orbital sanders fit among common sanding tools.
Use that overview to decide whether a random orbital sander is the right tool for the job, then return to the mounting pattern before ordering any replacement pad.
Our picks at a glance
-
1
Best for DeWalt 4-screw fitGnellkoor Orbital Sander Pad Replacement for Dewalt
9.7/10 our score
See it on Amazon -
2
Best for Bosch ROS10 and ROS20VSPoweka 5”ROS20vs Replacement Sanding Pad Compatible
9.6/10 our score
See it on Amazon -
3
Best for a pad and abrasive bundleNYXCL 5 inch DeWalt DWE6423/6423K
9.6/10 our score
See it on Amazon
- 4
Best for several 3-screw sandersCheck it - 5
Check itDEWALT Hook And Loop Pad for Sanders
Best for the matching DeWalt part
The best orbital sander replacement pads by fit and use
These replacement pads all use a 5-inch format, but they are not interchangeable by diameter alone. Check your sander model, mounting holes and dust-hole layout before choosing a pad.
Gnellkoor Orbital Sander Pad Replacement for Dewalt: Best for DeWalt 4-screw fit
- 5-inch pad
- 4 screw holes
- 8 dust holes
- 2-pack
A 5-inch DeWalt-compatible pad with a 4-screw mounting pattern and 8 dust holes. The 2-pack also includes foam and sanding discs.
Pros
- Clear 4-screw dimensions
- 8-hole dust design
- 2 replacement pads
Cons
- Screws are not included
Gnellkoor is the strongest overall pick for compatible DeWalt machines because it gives you a clear 5-inch size, a 4-screw mounting pattern and 8 dust holes. The stated non-adjacent screw-hole center distance is 1.97 inches, while the adjacent center distance is 1.38 inches.
That detail matters when replacing a random orbital sander pad. A pad can have the right diameter and still fail to line up with the tool if the screw positions differ.
The pad uses engineering plastics and soft rubber. The plastic provides the backing structure, while the soft rubber is intended to reduce vibration.
The hook-and-loop surface holds compatible sanding discs in place.
This set includes 2 replacement pads, 4 foam pieces and 36 sanding discs in 100, 150, 180, 240, 320 and 405 grit. The screws needed for installation are not included, so keep the original hardware if it remains usable.
Choose Gnellkoor when your DeWalt model matches the stated DWE6420, DWE6421, DWE6421K, DWE6423, DWE6423K or DCW210B compatibility. For a broader look at that brand-specific choice, see the best DeWalt orbital sander replacement pad guide.
Poweka 5”ROS20vs Replacement Sanding Pad Compatible: Best for Bosch ROS10 and ROS20VS
- 5-inch pad
- 8-hole design
- Rubber construction
- 2-count pack
This 5-inch rubber pad is made for Bosch ROS10, ROS20VS and ROS20VSK sanders using the RS035 fit. Its 8 holes support dust collection.
Pros
- Specific Bosch model coverage
- 8-hole dust collection
- 2 pads
Cons
- Not for Bosch 1250DEVS
Poweka is the best Bosch-focused choice here for ROS10, ROS20VS and ROS20VSK sanders using the RS035 fit. Its 5-inch rubber pad has 8 dust holes and comes as a 2-count pack.
The Bosch fit is the main reason to choose this pad. The stated compatible models include the ROS10 and ROS20VS variable-speed palm-grip random orbital sanders, plus the ROS20VSK kit.
The hard rubber pad is intended for flat surfaces and coarser abrasives. Its hook-and-loop surface holds the sanding disc while the 8-hole layout supports dust collection through the sander.
Poweka identifies this as a non-original aftermarket part. That does not make it a poor choice, but it makes model checking especially important.
The product is not intended for Bosch 1250DEVS, which uses other backing-pad options.
Pick Poweka when the RS035 fit matches your tool. If you need more Bosch-specific options, compare it with the best Bosch orbital sander replacement pad roundup.
NYXCL 5 inch DeWalt DWE6423/6423K: Best for a pad and abrasive bundle
- 5-inch 8-hole pad
- 4 foam interface pads
- 30 aluminum oxide discs
- 100 to 400 grit
The NYXCL set combines one replacement backing pad with foam interface pads and 30 sanding discs. It suits DeWalt owners who need replacement parts and abrasives together.
Pros
- Broad grit range
- Foam interface pads included
- 5-inch 8-hole format
Cons
- Only one replacement backing pad
NYXCL is the best choice when you need a replacement pad and a spread of sanding grits in one set. It includes one 5-inch 8-hole replacement pad, 4 soft foam interface pads and 30 aluminum oxide discs.
The replacement pad is made for DeWalt DWE6423, DWE6423K, DWE6421, DWE6421K and DCW210B sanders. It also covers the DWE6420 and listed DWE6421 variants.
The included discs range from 100 to 400 grit: 100, 150, 180, 240, 320 and 400. That range lets you move from heavier material removal toward finer surface preparation without buying a separate abrasive set immediately.
The 0.5-inch foam interface pads are useful when you need a softer layer between the backing pad and abrasive disc. They can help the abrasive follow contours, such as uneven wooden surfaces, but they also add another layer to the setup.
Choose NYXCL if the DeWalt compatibility matches and you want extra abrasives for wood sanding, metal grinding or polishing. For replacement components beyond the pad, see the guide to best Bosch orbital sander replacement parts as a model for what to check on other machines.
AxPower 5 inch 8 Hole Hook: Best for several 3-screw sanders
- 5-inch pad
- 8 dust holes
- 3 mounting screw holes
- 4-pack
AxPower uses a 3-screw mounting pattern and covers several older Makita, DeWalt, Porter Cable and Hitachi models. Four pads make it useful for planned replacements.
Pros
- 4-pack
- 3-screw pattern
- 8-hole dust collection
Cons
- Does not include screws
AxPower is the best fit for several older 3-screw, 5-inch random sanders. Its compatibility list includes selected Makita, DeWalt, Porter Cable and Hitachi models, and the package includes 4 replacement pads.
The mounting pattern is the key difference. AxPower uses 3 mounting screw holes, while Gnellkoor uses 4.
If your original pad has 3 screws, this layout may be the closer match, but confirm the exact model before ordering.
The pad has 8 dust holes and a hook-and-loop sanding surface. The rubber and plastic construction is intended for flat-surface sanding and surface preparation.
The listed compatible DeWalt models include DW420, DW421, DW423, DW426, D26453 and D26451. Makita coverage includes BO5010, BO5021, BO5030, BO5031, BO5041 and XOB01Z.
Four pads make this a useful option if you want replacements ready for future wear. Screws are not included, so retain the original mounting hardware where possible.
For the D26451 specifically, see best DeWalt orbital sander parts D26451.
DEWALT Hook And Loop Pad for Sanders: Best for the matching DeWalt part
- 5-inch pad
- 8-hole design
- DWE64233 model
- 1-count pack
This 5-inch, 8-hole pad is the DWE64233 replacement for compatible DeWalt DWE6423 and DWE6421 sanders. It is a single-pad option for a direct model match.
Pros
- Exact DWE64233 model
- 8-hole design
- Woven hook-and-loop retention material
Cons
- Only one pad
The DEWALT DWE64233 is the best choice when you want the named DeWalt replacement part for a compatible DWE6423 or DWE6421 sander. It is a single 5-inch, 8-hole hook-and-loop pad.
The 8-hole layout is designed for sanders with dust collection. The pad also uses a woven retention material, which supports repeated changes between sanding grits.
That woven surface matters during a longer job. It helps the disc stay seated while still letting you peel it away to inspect the surface or move to another grit.
This option is less flexible in quantity than the 2-packs and 4-packs above. Its advantage is the clear DWE64233 model and part-number match, which can reduce uncertainty when your sander uses that exact replacement.
Choose it when your tool is a DWE6423 or DWE6421 and you want one replacement pad. If you need a replacement dust bag as well, compare the best DeWalt orbital sander bag options.
What should you compare on an orbital sander replacement pad?
The most important comparison is diameter, mounting pattern and dust-hole layout. A 5-inch pad must also fit the screw locations and allow the sanding disc holes to align with the sander.
Diameter and sanding-disc size
All 5 products here use a 5-inch pad. That makes diameter easier to compare, but it does not remove the need to verify the model and mounting hardware.
A replacement pad should support the sanding discs made for your tool. If the diameter is wrong, the disc can extend beyond the pad or leave part of the pad unused.
Mounting screw pattern
Gnellkoor uses 4 screw holes with stated center distances. AxPower uses 3 screw holes and covers a different group of machines.
The Bosch Poweka pad uses the RS035 fit, while the DEWALT pad is identified as DWE64233.
Count the screws on your current pad before ordering. Then compare the hole positions, not just the number of holes.
Dust holes and collection
The products here use 8 dust holes, but the locations still need to line up. Dust collection works best when the pad and sanding disc allow dust to move through the sander's collection path.
For more setup ideas, read DeWalt orbital sander dust collection. Keep the holes clear and empty the dust bag or collector regularly.
Pad material and firmness
Rubber pads give the backing surface structure, while foam interface pads add a softer layer for contours. A firm pad is better suited to flat surfaces, while a foam interface can change how the abrasive follows an uneven shape.
The firm pad tends to keep pressure more even on boards, panels and other flat stock. That makes it a sensible default when you want predictable material removal.
A foam layer can soften that contact and help the disc follow gentle curves or uneven areas. It can also round edges a little more, so it suits preparation work where a sharp edge is not the goal.
Do not add an interface pad unless the job calls for it. Extra layers can change the sanding feel and may make edge control harder.
Think about the finish you need before you change the setup. If the surface is already flat, adding foam may not improve the result and could make fine control feel less direct.
How do you install a random orbital sander pad?
Start by unplugging the sander or removing its battery. Place it on a stable surface, remove the old mounting screws, clean away loose dust, and align the replacement pad with the original screw positions.
Keep the old screws in a safe place as you work. Some replacement pads do not include new screws, so losing the originals can leave you with a pad you cannot fit.
Check the face of the sander before the new pad goes on. Dust left under the pad can stop it sitting flat, and that small gap can show up as uneven sanding.
Tighten the screws evenly without forcing them. Before sanding, press a compatible disc onto the hook-and-loop surface and confirm that the disc holes line up with the pad holes.
Press around the edge of the disc as well as the centre. A disc that feels secure in the middle but lifts at the rim may shift once the sander starts moving.
Run the sander briefly on a clear surface. Stop if the pad wobbles, the disc shifts or the tool makes an unusual sound.
That short trial is a good point to check the setup with the tool off again. Reseat the disc if needed and look again at the screws before you move to the workpiece.
Recheck the mounting pattern and screw seating before continuing. Small corrections are easier at this stage than after you have started sanding.
Keep the pad surface free of packed dust. Replace it when the hook-and-loop surface no longer holds discs securely or when the pad is damaged.
A quick clean after each session can help you spot wear early. Look for torn edges, loose hooks or holes that no longer line up with the disc.
Store the sander so the pad is not pressed against a hard edge. That protects the hook surface and keeps the next setup more consistent.
How can you choose the right random orbital sander pad replacement?
Choose Gnellkoor for a DeWalt machine with the stated 4-screw fit, Poweka for Bosch ROS10 or ROS20VS compatibility, and AxPower for listed 3-screw Makita, DeWalt, Porter Cable or Hitachi models. Choose NYXCL when extra discs and foam interface pads matter.
Those choices cover different starting points. A 4-screw DeWalt, a Bosch RS035 fit and an older 3-screw machine may all take a 5-inch pad, but that does not make the pads interchangeable.
The DEWALT DWE64233 is the simpler choice when your tool matches the DWE6423 or DWE6421 model family and you want the named replacement part. For another brand-specific comparison, see the best Bauer sander replacement pad guide.
Check the original pad before ordering. Record its diameter, screw count, screw positions and dust-hole layout, then match those details to the replacement.
Diameter is only the first check. A pad of the right size may still have the wrong screw spacing or a dust-hole layout that does not match your discs.
Screw count is the next check. Count the holes on the old pad and note their positions, since two pads with the same count can still mount differently.
Dust holes deserve the same care. Their positions need to line up with both the sander and the sanding disc if you want dust collection to work as intended.
Model coverage is the final check. Compare the sander model on the tool or manual with the compatibility list for the pad, rather than relying on size alone.
Consider how the pad will be used after it fits. Flat work usually suits a firmer pad, while contoured work may call for a foam interface layer between pad and disc.
Also think about quantity and included supplies. A single pad may be enough for a direct replacement, while a bundle with discs can suit a workshop that needs grits on hand.
Keep the original screws safe during the swap. Some pads are supplied without screws, so the existing hardware may be needed to complete the installation.
For daily care, keep the hook surface clean and inspect it for packed dust before each use. A clean pad holds discs more evenly and makes changing grits easier.
Verdict
The Gnellkoor Orbital Sander Pad Replacement for Dewalt is the best overall choice for its stated DeWalt compatibility, 4-screw pattern, 8 dust holes and 2-pad package. Choose Poweka for Bosch ROS10 or ROS20VS sanders, NYXCL for a pad-and-abrasive bundle, AxPower for a 3-screw multi-brand fit, and DEWALT for the DWE64233 model match.
The right pick depends first on your sander model. Match the diameter, screw pattern and dust-hole layout before you compare anything else.
Once fit is confirmed, think about the work ahead. Flat surfaces, contoured pieces and changeovers between grits can all favour a slightly different setup.
Keep the pad clean, check the disc seating before each session, and replace the pad when it no longer holds a disc firmly. Those habits will get more consistent results from whichever pad fits your tool.
Our top 3 picks at a glance
-
1
Best for DeWalt 4-screw fitGnellkoor Orbital Sander Pad Replacement for Dewalt
9.7/10 our score
See it on Amazon -
2
Best for Bosch ROS10 and ROS20VSPoweka 5”ROS20vs Replacement Sanding Pad Compatible
9.6/10 our score
See it on Amazon -
3
Best for a pad and abrasive bundleNYXCL 5 inch DeWalt DWE6423/6423K
9.6/10 our score
See it on Amazon
Frequently asked questions
How do I choose an orbital sander replacement pad?
Match the pad diameter, mounting screw pattern and dust-hole layout to your sander. Most options here are 5 inches, but the mounting pattern differs: Gnellkoor uses 4 screw holes, while AxPower uses 3.
Confirm the model and hole positions before ordering.
Are orbital sander pads universal?
No. A 5-inch diameter alone does not prove a fit.
The screw pattern, hole layout and model compatibility also matter.
For example, Poweka is made for the Bosch RS035 fit, while the DEWALT DWE64233 is designed for specific DeWalt sanders.
How many dust holes should a replacement pad have?
The number must match the sander's sanding-disc and dust-collection layout. The products here use 8-hole designs, but the hole positions still need to line up.
A matching layout helps dust move into the dust bag or collection system.
Can I replace an orbital sander pad myself?
Yes, if the replacement matches your sander and you can access the mounting screws. Remove the old pad, keep track of the screws, align the new pad with the tool, and tighten it evenly.
Gnellkoor and AxPower note that screws are not included.
About this guide: Our look at orbital sander replacement pads draws on maker specs, materials and what owners report. See how we research.



