How to Square a Table Saw Blade
To square a table saw blade, set it to 90 degrees and align a tooth with the miter slot using a reliable measuring tool. Compare the front and rear readings, then adjust the trunnion or blade alignment as your saw manual directs.
On this page (9 sections)
- How do you square a table saw blade to the table?
- How do you check blade alignment with the miter slot?
- How do you adjust a misaligned table saw blade?
- How can you tell whether the fence is also aligned?
- What should you check before making a test cut?
- Which tools help with accurate table saw cuts?
- How do you square a crosscut sled after aligning the blade?
- When should you stop and check the saw manual?
- What is the reliable order for squaring a table saw blade?
To square a table saw blade, set it to 90 degrees and align a tooth with the miter slot using a reliable square or alignment gauge. Compare the front and rear readings, then adjust the saw as its manual directs.
A blade that isn't square to the table can make bevel cuts inaccurate. If it isn't parallel to the miter slot, a workpiece may bind or drift during a cut.
How do you square a table saw blade to the table?
Raise the blade, set its tilt to 90 degrees, and check it against the table with a reliable square. Unplug the saw before adjusting or measuring near the blade, and follow the manual's instructions for the arbor, insert, and blade tilt.
- Disconnect the saw from power and remove the throat plate if the manual says to.
- Raise the blade to a useful height.
- Set the bevel scale to 90 degrees, then check the blade face with a square.
- If the angle is off, adjust the 90-degree stop or tilt mechanism as the manual describes.
- Recheck the angle after tightening any adjustment.
Check a tooth or the blade body as your tool instructions recommend. Avoid a carbide tooth when its shape or set could make the reading uneven.
The bevel scale is a reference, not proof of squareness. Verify the blade itself before relying on it for accurate cuts.
How do you check blade alignment with the miter slot?
Measure from the same blade tooth to the miter slot at the front and rear. A consistent tooth and measuring point make the comparison useful.
With the saw unplugged, turn the blade by hand to place a marked tooth at the front measurement point. Use an alignment gauge or another suitable measuring tool to record the distance from that tooth to one edge of the miter slot.
Rotate the blade so that same tooth is at the rear, keeping the measuring tool on the same slot edge. Compare the two readings; don't measure from different teeth, because blade runout can make the difference misleading.
A straightedge and feeler gauges can help with some setups, but the method depends on the saw and the tools available. Use the tolerance and measurement method in the saw manual rather than guessing at a universal number.
What does it mean if the front and rear readings differ?
A difference means the blade and miter slot aren't parallel at the measurement points. Repeat the check to rule out a positioning error before making an adjustment.
Confirm that the blade is clean, the marked tooth is the same, and the measuring tool contacts the slot and blade consistently. If the readings still differ, consult the manual for its alignment procedure.
How do you adjust a misaligned table saw blade?
Use the adjustment method specified for your saw model. Some saws allow the trunnion or table to be repositioned, while others use a different mechanism.
Unplug the saw and remove only the covers or parts described in the manual. Make small adjustments, tighten fasteners as directed, then remeasure at the front and rear.
Don't force a stuck bolt or loosen hardware without knowing what it supports. If the manual doesn't explain the procedure or the saw still won't align, ask a qualified repair technician.
After adjusting alignment, check the blade's 90-degree stop again. One adjustment can affect the other, so verify both before making a test cut.
How can you tell whether the fence is also aligned?
Check the fence against the miter slot separately from the blade. A fence that points inward toward the blade can pinch a workpiece even when the blade is aligned.
If your saw is a Delta and its fence needs replacing, compare Delta table saw fences.
If the fence needs replacing, check which replacement fence fits your DeWalt table saw before buying.
Use a straightedge or suitable gauge to compare the fence's distance from the same miter slot edge at the front and rear. Follow your saw manual's guidance on fence alignment and any intentional toe-out.
If you use a featherboard, set it to press the workpiece against the fence without forcing it sideways. The best table saw jigs can help with repeatable setups, but they don't replace alignment checks.
A fence extension can add support for long or wide stock, but confirm that it fits your saw and doesn't change fence alignment. Compare table saw fence extensions if you need more support.
What should you check before making a test cut?
Restore the guards and inserts, remove tools from the table, and reconnect power only after the adjustment is complete. Make a test cut on scrap while keeping your hands clear of the blade.
Use the blade guard and riving knife where the saw manual and cut type allow them. Stand out of the line of possible kickback, and use a push stick or push block when the cut requires one.
A featherboard can help keep stock against the fence when it's positioned and secured correctly. The BOW Products EVA Featherboard has interchangeable feathers and a miter bar for a standard slot.

Its EVA feathers and miter bar can help guide stock against the fence during a suitable rip cut.
See it on AmazonA featherboard is a feed-control aid, not a blade-alignment tool or a substitute for safe technique. Set it before starting the saw, and keep it clear of the blade and cut path.
Which tools help with accurate table saw cuts?
Use a square or alignment gauge to check the blade, and use a miter gauge for guided crosscuts. Each tool addresses a different part of setup.
The POWERTEC 71391 Table Saw Precision Miter Gauge has 27 angle stops and a fence with a measuring scale. Its miter bar fits a standard 3/4 in by 3/8 in slot, so check your saw's slot before choosing it.

Its angle stops and fence can help set repeatable crosscuts after you verify the saw's alignment.
See it on AmazonThe Hedgehog Spiral Featherboard has a single pivot knob and a reversible design for left- or right-side feed. It fits standard 3/4 in by 3/8 in miter slots, so measure your slot first.

Its quick adjustment can help maintain pressure against the fence during compatible feed setups.
See it on AmazonNeither accessory squares the blade. For bevel cuts, first set and check the blade angle; for crosscuts, also check the miter gauge and sled.
How do you square a crosscut sled after aligning the blade?
Check the sled against the blade only after the blade and miter slots are aligned. A misaligned saw can make a properly adjusted sled seem inaccurate.
Make a test cut using a straight, stable piece of scrap, then check the cut for square. Adjust the sled fence in small steps and repeat the test until it meets your accuracy needs.
Follow how to square a crosscut sled for the sled adjustment process. For a different saw setup, see how does a miter saw differ from a table saw?.
When should you stop and check the saw manual?
Stop if the blade wobbles, the arbor feels loose, an adjustment binds, or readings keep changing. Those signs can point to a problem beyond a simple alignment correction.
Use the blade and accessories approved for your saw, and never make adjustments with power connected. If you use a different cutting setup, how a circular saw differs from a table saw explains the basic distinction, while guide rails for Festool and Makita track saws cover a separate guided-cutting approach.
For a DeWalt saw, confirm that any featherboard fits its slot and setup before buying; see featherboards for DeWalt table saws. If you own a Craftsman saw, check the fence model and mounting arrangement in fences for Craftsman table saws.
What is the reliable order for squaring a table saw blade?
Check the blade's 90-degree angle first, then compare its alignment to the miter slot, and verify the fence separately. Make one adjustment at a time and recheck each measurement.
Use the saw manual's procedure and tolerance for alignment. If the readings are stable and the test cut is accurate, return to work with the guard and safety equipment in place.
Frequently asked questions
How do you check whether a table saw blade is square?
Unplug the saw, raise the blade, and set it to 90 degrees. Use a reliable square or alignment gauge to compare the same blade tooth with the miter slot at the front and rear of the table.
A difference between those readings points to alignment that needs checking.
Should a table saw blade be parallel to the miter slot?
The blade should be aligned parallel to the miter slot within the tolerance stated in your saw manual. Check at the front and rear with the same tooth and measuring point, then use the manual's adjustment method if the readings differ.
Why does my table saw cut burn marks?
Burn marks can come from several causes, including a misaligned blade or fence, a dull or dirty blade, or feed pressure that is too slow. Check alignment and the saw manual, and disconnect power before inspecting or adjusting the blade.
Can I use a miter gauge to square a table saw blade?
A miter gauge can help guide a test cut, but it doesn't measure blade alignment to the miter slot by itself. Use a square or suitable alignment gauge for the blade check, then verify the miter gauge separately if crosscuts are inaccurate.
About this guide: Our look at squaring a table saw blade draws on maker specs, materials and what owners report. See how we research.



